.. _section-micro_and_core: Working with |rti_me_h| and |rti_core_h| ======================================== In some cases, it may be necessary to write an application that is compiled against both |rti_me| and |rti_core|. In general this is not easy to do because |rti_me| supports a very limited set of features compared to |rti_core|. However, due to the nature of the DDS API and the philosophy of declaring behavior through QoS profiles instead of using different APIs, it may be possible to share common code. In particular, |rti_core| supports configuration through QoS profile files, which eases the job of writing portable code. Please refer to :doc:`../introduction` for an overview of features and what is supported by |rti_me|. Note that |rti_core| supports many extended APIs that are not covered by the DDS specification, for example APIs that create DDS entities based on QoS profiles. Development Environment ----------------------- There are no conflicts between |rti_me| and |rti_core| with respect to library names, header files, etc. It is advisable to keep the two installations separate, which is the normal case. |rti_me| uses the environment variable RTIMEHOME to locate the root of the |rti_me| installation. |rti_core| uses the environment variable NDDSHOME to locate the root of the |rti_core| installation. Non-standard APIs ----------------- The DDS specification omits many APIs and policies necessary to configure a DDS application, such as transport, discovery, memory, logging, etc. In general, |rti_me| and |rti_core| do not share APIs for these functions. It is recommended to configure |rti_core| using QoS profiles as much as possible. QoS Policies ------------ QoS policies defined by the DDS standard behave the same between |rti_me| and |rti_core|. However, note that |rti_me| does not always support all the values for a policy and in particular unlimited resources are not supported. Unsupported QoS policies are the most likely reason for not being able to switch between |rti_me| and |rti_core|. Standard APIs ------------- APIs that are defined by the standard behave the same between |rti_me| and |rti_core|. IDL Files --------- |rti_me| and |rti_core| use the same IDL compiler (rtiddsgen) and |rti_me| typically ships with the latest version. However, |rti_me| and |rti_core| use different templates to generate code and it is not possible to share the generated code. Thus, while the same IDL can be used, the generated output must be saved in different locations. @section microcore_interop Interoperability In general, |rti_me| and |rti_core| are wire interoperable, unless noted otherwise. All RTI products, aside from |rti_me|, are based on |rti_core|. Thus, in general |rti_me| is compatible with RTI tools and other products. The following sections provide additional information for each product. When trying to establish communication between an |rti_me| application that uses the Dynamic Participant / Static Endpoint (DPSE) discovery module and an RTI product based on |rti_core|, every participant in the DDS system must be configured with a unique participant name. While the static discovery functionality provided by |rti_core| allows participants on different hosts to share the same name, |rti_me| requires every participant to have a different name to help keep the complexity of its implementation suitable for smaller targets. Admin Console ------------- Admin Console can discover and display |rti_me| applications that use full dynamic discovery (DPDE). When using static discovery (DPSE), it is required to use the Limited Bandwidth Endpoint Discovery (LBED) that is available as a separate product for |rti_core|. With the library a configuration file with the discovery configuration must be provided (just as in the case for products such as Routing Service, etc.). This is provided through the QoS XML file. Data can be visualized from |rti_me| DataWriters. Keep in mind that |rti_me| does not currently distribute type information and the type information has to be provided through an XML file using the "Create Subscription" dialog. Unlike some other products, this information cannot be provided through the QoS XML file. To provide the data types to Admin Console, first run the code generator with the ``-convertToXml`` option: :: rtiddsgen -convertToXml Then click on the “Load Data Types from XML file” hyperlink in the "Create Subscription" dialog and add the generated IDL file. Other Features Supported: - Match analysis is supported. - Discovery-based QoS are shown. The following resource-limits in |rti_me| must be incremented as follows when using Admin Console: - Add 24 to DDS_DomainParticipantResourceLimitsQosPolicy::remote_reader_allocation - Add 24 to DDS_DomainParticipantResourceLimitsQosPolicy::remote_writer_allocation - Add 1 to DDS_DomainParticipantResourceLimitsQosPolic::remote_participant_allocation - Add 1 to DDS_DomainParticipantResourceLimitsQosPolicy::remote_participant_allocation if data-visualization is used |rti_me| does not currently support any administration capabilities or services, and does not match with the Admin Console DataReaders and DataWriters. However, if matching DataReaders and DataWriters are created, e.g., by the application, the following resource must be updated: - Add 48 to DDS_DomainParticipantResourceLimitsQosPolicy::matching_writer_reader_pair_allocation Distributed Logger ------------------ This product is not supported by |rti_me|. LabVIEW ------- The LabVIEW toolkit uses |rti_core|, and it must be configured as any other |rti_core| application. A possible option is to use the builtin |rti_core| profile: BuiltinQosLib::Generic.ConnextMicroCompatibility. Monitor ------- This product is not supported by |rti_me|. Recording Service ----------------- RTI Recorder ............ RTI Recorder is compatible with |rti_me| in the following ways: - If static endpoint discovery is used, Recorder is compatible starting with version 5.1.0.3 and onwards. - If dynamic endpoint discovery is used, Recorder is compatible with |rti_me| the same way it is with any other DDS application. - In both cases, type information has to be provided via XML. Read |rti_micro_record|_ for more information. RTI Replay .......... RTI Replay is compatible with |rti_me| in the following ways: - If static endpoint discovery is used, Replay is compatible starting with version 5.1.0.3 and onwards. - If dynamic endpoint discovery is used, Replay is compatible with |rti_me| the same way it is with any other DDS application. - In both cases, type information has to be provided via XML. Read |rti_micro_record|_ for more information on how to convert from IDL to XML. RTI Converter ............. Databases recorded with |rti_me| contains no type information in the DCPSPublication table, but the type information can be provided via XML. Read |rti_micro_record|_ for more information on how to convert from IDL to XML. Spreadsheet Addin ----------------- |rti_me| can be used with Spreadsheet Add-in starting with version 5.2.0. The type information must be loaded from XML files. Wireshark --------- Wireshark fully supports |rti_me|. Persistence Service ------------------- |rti_me| only supports VOLATILE and TRANSIENT_LOCAL durability and does not support the use of Persistence Service.