1.2.4. C# API

The following tests have been performed by executing an RTI Perftest C# Publisher and Subscriber between two nodes, connected to a switch via Ethernet. The communication has been restricted to a single interface and the transport has been set to UDPv4.

Find information about the hardware, network, and command-line parameters after each of the tests.

1.2.4.1. Unkeyed, UDPv4 10Gbps Network, C#

Linux x64

Minimum LatencyMaximum Throughput

The graph below shows the one-way latency without load between a Publisher and a Subscriber running in two Linux nodes in a 10Gbps network. The numbers are for best-effort as well as strict reliable reliability scenarios.

Note

We use the median (50th percentile) instead of the average in order to get a more stable measurement that does not account for spurious outliers. We also calculate the average value and other percentile values, which can be seen in the Detailed Statistics section below.

Detailed Statistics

The following tables contain the raw numbers presented by a simplified version of RTI Perftest for the Modern C# implementation. These numbers are the exact output with no further processing.

• Best Effort

Sample Size (Bytes)	Ave (μs)	Std (μs)	Min (μs)	Max (μs)	50% (μs)	90% (μs)	99% (μs)	99.99% (μs)	99.9999% (μs)
32	17	3.2	16	465	17	18	19	26	465
64	18	1.7	17	463	18	18	20	27	463
128	17	5.7	17	467	18	18	19	27	467
256	18	3.9	18	476	18	19	20	28	476
512	19	4.8	18	484	19	21	22	29	484
1024	25	6.5	19	491	26	31	32	40	491
2048	29	10.4	23	968	30	33	58	299	968
4096	33	138.0	26	100066	30	38	65	72	100066
8192	44	11.3	37	512	40	59	62	123	512
16384	93	28.7	49	578	84	128	134	142	578
32768	139	23.7	88	641	134	168	181	190	641
63000	191	20.5	135	1254	189	211	221	237	1254

• Reliable

Sample Size (Bytes)	Ave (μs)	Std (μs)	Min (μs)	Max (μs)	50% (μs)	90% (μs)	99% (μs)	99.99% (μs)	99.9999% (μs)
32	19	4.7	18	490	19	20	22	36	490
64	17	4.0	15	1272	17	17	25	82	1272
128	19	4.6	18	476	19	20	22	39	476
256	21	7.1	18	470	20	30	39	47	470
512	22	8.2	19	479	21	32	41	49	479
1024	26	5.1	20	482	26	29	55	60	482
2048	29	10.4	23	968	30	33	58	299	968
4096	31	10.1	27	924	31	34	59	560	924
8192	46	12.2	39	843	41	60	83	122	843
16384	93	28.7	49	578	84	128	134	142	578
32768	139	23.7	88	641	134	168	181	190	641
63000	191	20.5	135	1254	189	211	221	237	1254
100000	216	17.8	168	1800	218	230	248	278	1800
500000	677	69.2	559	8061	679	713	721	774	8061
1048576	1368	181.8	1244	16449	1356	1439	1468	16449	16449
1548576	1940	328.8	1760	25178	1936	1956	1977	25178	25178
4194304	5287	1856.9	4807	85992	5244	5270	5297	85992	85992
10485760	12505	6581.9	12230	198530	12267	12293	12322	198530	198530

Perftest Scripts

To produce these tests, we executed RTI Perftest for C#. The exact script used can be found here:

#!/bin/bash
filename=$0
script_location=$(cd "$(dirname "$filename")" || exit 255; pwd)

export datasizes="32 64 128 256 512 1024 2048 4096 8192 16384 32768 63000"
export datasizes_extended="${datasizes} 100000 500000 1048576 1548576 4194304 10485760"

export domain="2"
export exec_time=20
export num_reps=1
export instance_number=100000
export core=0

# We will use some colors to improve visibility of errors and info messages.
RED='\033[0;31m'
GREEN='\033[0;32m'
YELLOW='\033[0;33m'
BLUE='\033[0;34m'
LIGHTBLUE='\033[0;36m'
NC='\033[0m'
INFO_TAG="${GREEN}[INFO]:${NC}"
WARNING_TAG="${YELLOW}[WARNING]:${NC}"
ERROR_TAG="${RED}[ERROR]:${NC}"

export ip_machine_1="10.2.75.20"
export ip_machine_2="10.2.75.21"
export if10Gbps="enp1s0f0"
export if1Gbps="eno1"

################################################################################

function disable_colors() {
    export RED=""
    export GREEN=""
    export YELLOW=""
    export NC=""
    export BLUE=""
    export LIGHTBLUE=""
    export INFO_TAG="${GREEN}[INFO]:${NC}"
    export WARNING_TAG="${YELLOW}[WARNING]:${NC}"
    export ERROR_TAG="${RED}[ERROR]:${NC}"
}

function change_domain() {
    if [[ "$domain" == "1" ]]; then
        export domain="2"
    else
        export domain="1"
    fi
}

# Usage: execute_test <keyed/unkeyed> <rel/be> <datasizes> <batchSize>
function execute_test() {

    local keyed_unkeyed=$1
    local rel_be=$2
    local datasizes_test=$3
    local other_args=$4
    local name_suffix=$5

    local commands_string_test=$commands_string
    local tag=""

    if [[ "${keyed_unkeyed}" == "keyed" ]]; then
        commands_string_test="${commands_string_test} -keyed -instances $instance_number"
        tag="[${YELLOW}${transport}${NC}|${BLUE}K${NC}|"
    else
        tag="[${YELLOW}${transport}${NC}|${LIGHTBLUE}UK${NC}|"
    fi

    if [[ "${rel_be}" == "be" ]]; then
        commands_string_test="${commands_string_test} -bestEffort"
        tag="${tag}${YELLOW}BE${NC}]"
    else
        tag="${tag}${RED}REL${NC}]"
    fi

    tag="${tag}[${LIGHTBLUE}${lat_thr}${NC}]"

    local output_file=$output_folder/${lat_thr}_${role}_${keyed_unkeyed}_${rel_be}${name_suffix}.csv

    if [[ "$role" == "pub" ]]; then
        echo -e "${YELLOW}[TEST]: $keyed_unkeyed, $rel_be. ${NC}"
    fi

    if [[ "$LANGUAGE" != "java" && "$LANGUAGE" != "cs" ]]; then
        export pre_command_string="taskset -c $core"
    fi

    # Get the aprox time this will take:
    total_tests=$((`wc -w <<< "$datasizes_test"` * num_reps))
    total_time=$((total_tests * exec_time))

    touch $output_file
    local no_headers=""
    local current_test=0
    for index in $(seq 1 ${num_reps}); do
        for DATALEN in ${datasizes_test}; do
            current_test=$((current_test + 1))
            export command="$pre_command_string $executable -domain $domain -dataLen $DATALEN $commands_string_test $other_args $no_headers"
            if [[ "$role" == "pub" ]]; then
                echo -e "Test ${tag} (${current_test}/${total_tests}) -- Total time = ${total_time}s"
                echo -e ${BLUE}$command${NC}
            else
                echo -e ${LIGHTBLUE}$command${NC}
            fi
            if [[ "$LANGUAGE" == "cs" && "$role" == "pub" ]]; then
                sleep 3
            fi
            $command >> $output_file;
            no_headers=" -noOutputHeaders"
            change_domain
        done
    done
}

################################################################################
# PARSE COMMAND LINE OPTIONS:

while [ "$1" != "" ]; do
    case $1 in
        --executable)
            executable=$2
            shift
            ;;
        --output-folder)
            output_folder=$2
            shift
            ;;
        --role)
            export role=$2
            shift
            ;;
        --core)
            export core=$2
            shift
            ;;
        --test-kind)
            export lat_thr=$2
            shift
            ;;
        --interface1)
            export interface=$2
            shift
            ;;
        --interface2)
            export interface2=$2
            shift
            ;;
        --ip1)
            export ip1=$2
            shift
            ;;
        --ip2)
            export ip2=$2
            shift
            ;;
        --repetitions)
            export num_reps=$2
            shift
            ;;
        --domain)
            export domain=$2
            shift
            ;;
        --execution-time)
            export exec_time=$2
            shift
            ;;
        --transport)
            export transport=$2
            shift
            ;;
        --datalen)
            export datalen_input=$2
            shift
            ;;
        --file-suffix)
            export file_suffix=$2
            shift
            ;;
        --executable-suffix)
            export executable_suffix=$2
            shift
            ;;
        --extra-arguments)
            export extra_arguments=$2
            shift
            ;;
        --extra-arguments-pub)
            export extra_arguments_pub=$2
            shift
            ;;
        --extra-arguments-sub)
            export extra_arguments_sub=$2
            shift
            ;;
        --skip-no-batching)
            export skip_no_batching="1"
            ;;
        --skip-be)
            export skip_be_tests="1"
            ;;
        --skip-rel)
            export skip_rel_tests="1"
            ;;
        --skip-keyed)
            export skip_keyed_data="1"
            ;;
        --skip-large-data)
            export skip_large_data="1"
            ;;
        --large-data)
            export large_data="1"
            ;;
        --keyed)
            export skip_unkeyed="1"
            ;;
        --unkeyed)
            export skip_keyed_data="1"
            ;;
        --no-batching)
            export no_batching_only="1"
            ;;
        --reliable)
            export skip_be_tests="1"
            ;;
        --best-effort)
            export skip_rel_tests="1"
            ;;
        --security)
            export security_only="$2"
            shift
            ;;
        --micro)
            export micro="1"
            ;;
        --tss)
            export tss="1"
            ;;
        --no-colors)
            export NO_COLORS="1"
            ;;
        --language)
            export LANGUAGE=$2
            shift
            ;;
        *)
            echo -e "unknown parameter \"$1\""
            exit 255
            ;;
    esac
    shift
done

if [[ "$NO_COLORS" == "1" ]]; then
    disable_colors
fi

export folder_base="$(dirname "${executable}")"/../../..

if [[ $LANGUAGE == "java"  || "$LANGUAGE" == "cs" ]]; then
    export folder_base="$(dirname "${executable}")"/../..
fi
if [[ $tss == "1" ]]; then
    export folder_base="$(dirname "${executable}")"/../../../../..
fi

if [[ "${executable_suffix}" != "" ]]; then
    export executable="${executable}${executable_suffix}"
fi

echo -e "${INFO_TAG} Perftest executable is: $executable"
echo -e "${INFO_TAG} Output folder is: $output_folder"

################################################################################

if [[ "${skip_large_data}" == "1" ]]; then
    export datasizes_extended=${datasizes}
elif [[ "${large_data}" == "1" ]]; then
    export datasizes=${datasizes_extended}
fi

if [[ "${datalen_input}" != "" ]]; then
    echo -e "${YELLOW}[TEST] Testing only for ${datalen_input}${NC}"
    export datasizes=${datalen_input}
    export datasizes_extended=${datalen_input}
    if [[ "${no_batching_only}" != "1" ]]; then
        export skip_large_data="1"
    fi
fi

if [[ "$role" != "pub" && "$role" != "sub" ]]; then
    echo -e "${ERROR_TAG} It must be either publisher or subscriber"
    exit 255
fi

if [[ "$lat_thr" != "thr" && "$lat_thr" != "lat" ]]; then
    echo -e "${ERROR_TAG} It must be either lat or thr"
    exit 255
fi

if [[ "${interface}" == "" ]]; then
    echo "Using default nics"
    export nic_publisher=${ip_machine_1}
    export nic_subscriber=${ip_machine_2}
else
    export nic_publisher=$interface
    echo -e "${INFO_TAG} Using nic_publisher: ${nic_publisher}"

    if [[ "${interface2}" == "" ]]; then
        export nic_subscriber=$interface
    else
        export nic_subscriber=$interface2
    fi
    echo -e "${INFO_TAG} Using nic_subscriber: ${nic_subscriber}"

    if [[ "${ip1}" != "" ]]; then
        export ip_publisher=$ip1
        echo "Using ip_publisher: ${ip_publisher}"
    fi

    if [[ "${ip2}" != "" ]]; then
        export ip_subscriber=$ip2
        echo "Using ip_subscriber: ${ip_subscriber}"
    fi

fi

export transport_string="-transport $transport"

if [[ "$transport" == "UDPv4" ]]; then

    export transport_string_pub="$transport_string -nic $nic_publisher"
    export transport_string_sub="$transport_string -nic $nic_subscriber"

    if [[ "$micro" == "1" ]]; then
        export transport_string_pub="$transport_string_pub -peer ${ip_subscriber}"
        export transport_string_sub="$transport_string_sub -peer ${ip_publisher}"
    fi

elif [[ "$transport" == "TCP" ]]; then
    export transport_string_pub="$transport_string \
        -nic $nic_publisher \
        -peer 0@tcpv4_lan://${ip_subscriber}:7400"
    export transport_string_sub="$transport_string \
        -nic $nic_subscriber \
        -peer 0@tcpv4_lan://${ip_publisher}:7400"
elif [[ "$transport" == "TLS" ]]; then
    export transport_string_pub="$transport_string \
        -nic $nic_publisher \
        -peer tlsv4_lan://${ip_subscriber}:7400"
    export transport_string_sub="$transport_string \
        -nic $nic_subscriber \
        -peer tlsv4_lan://${ip_publisher}:7400"
elif [[ "$transport" == "UDPv4_WAN" ]]; then
    export transport_string_pub="$transport_string \
        -nic $nic_publisher \
        -transportPublicAddress $ip_publisher:7400"
    export transport_string_sub="$transport_string \
        -nic $nic_subscriber \
        -peer 0@udpv4_wan://${ip_publisher}:7400"
else
    export transport_string_pub="$transport_string"
    export transport_string_sub="$transport_string"
fi

################################################################################

export pub_string="-pub \
        ${transport_string_pub} \
        -noPrintIntervals \
        -executionTime $exec_time"

if [[ ${lat_thr} == "lat" ]]; then
    export pub_string="$pub_string \
        -latencyTest"
fi

export sub_string="-sub \
        ${transport_string_sub} \
        -noPrintIntervals"

if [[ "$role" == "pub" ]]; then
    echo -e "$INFO_TAG Publisher side running"
    export commands_string=${pub_string}
    export extra_arguments="${extra_arguments} ${extra_arguments_pub}"
else
    echo -e "$INFO_TAG Subscriber side running"
    export commands_string=${sub_string}
    export extra_arguments="${extra_arguments} ${extra_arguments_sub}"
fi

###############################################################################

echo -e "${INFO_TAG} Executing: /set_${lat_thr}_mode.sh"
sudo /set_${lat_thr}_mode.sh
sleep 5

cd $folder_base
echo -e "${INFO_TAG} Folder Base is: $PWD"
mkdir -p $output_folder

# Tests that may use batching (when doing throughput tests)
if [[ ${no_batching_only} != "1" ]]; then

    # UNKEYED
    if [[ "${skip_unkeyed}" == "" ]]; then

        # RELIABLE
        if [[ "${skip_rel_tests}" == "" ]]; then
            execute_test "unkeyed" "rel" "${datasizes_extended}" "${extra_arguments}" "$file_suffix"
        fi

        # BEST EFFORT
        if [[ "${skip_be_tests}" == "" ]]; then
            execute_test "unkeyed" "be" "${datasizes}" "${extra_arguments}" "$file_suffix"
        fi
    fi

    # KEYED
    if [[ "${skip_keyed_data}" == "" ]]; then

        # RELIABLE
        if [[ "${skip_rel_tests}" == "" ]]; then
            execute_test "keyed" "rel" "${datasizes}" "${extra_arguments}" "$file_suffix"
        fi

        # BEST EFFORT
        if [[ "${skip_be_tests}" == "" ]]; then
            execute_test "keyed" "be" "${datasizes}" "${extra_arguments}" "$file_suffix"
        fi
    fi

fi

if [[ "${skip_no_batching}" == "" || "${no_batching_only}" == "1" ]]; then
    no_batching_tests="1"
fi

# Tests that will not use batching
if [[ "${lat_thr}" == "thr" && "${no_batching_tests}" == "1" ]]; then

    if [[ "$role" == "pub" ]]; then
        export commands_string="${commands_string} -batchSize 0"
    fi

    # UNKEYED
    if [[ "${skip_unkeyed}" == "" ]]; then

        # RELIABLE
        if [[ "${skip_rel_tests}" == "" ]]; then
            execute_test "unkeyed" "rel" "${datasizes}" "${extra_arguments}" "_noBatch${file_suffix}"
        fi

        # BEST EFFORT
        if [[ "${skip_be_tests}" == "" ]]; then
            execute_test "unkeyed" "be" "${datasizes}" "${extra_arguments}" "_noBatch${file_suffix}"
        fi
    fi
fi

#!/bin/bash
filename=$0
script_location=$(cd "$(dirname "$filename")" || exit 255; pwd)

echo -e "[Calling base_script/script.sh]"
"${script_location}/../base_script/script.sh" $@ --transport UDPv4

Test Hardware

The following hardware was used to perform these tests:

Linux Nodes

Dell R340 Servers (13 Units)
Processor: Intel Xeon E-2278G (3.4-5GHz, 8c/16t, 16MB cache, 2 memory channels @2666MHz)
RAM: 4x 16GB 2666MHz DIMM (64GB RAM)
HD: 480GB SATA SSD
NIC 1: Intel 710 dual port 10Gbps SFP
OS: Ubuntu 20.04 -- gcc 9.3.0

Switch

Dell 2048 -- 10Gbps switch

1.2.4.2. Keyed, UDPv4 10Gbps Network, C#

Linux x64

Minimum LatencyMaximum Throughput

The graph below shows the one-way latency without load between a Publisher and a Subscriber running in two Linux nodes in a 10Gbps network. The numbers are for best-effort as well as strict reliable reliability scenarios.

Note

We use the median (50th percentile) instead of the average in order to get a more stable measurement that does not account for spurious outliers. We also calculate the average value and other percentile values, which can be seen in the Detailed Statistics section below.

Detailed Statistics

The following tables contain the raw numbers presented by a simplified version of RTI Perftest for the Modern C# implementation. These numbers are the exact output with no further processing.

• Best Effort

Sample Size (Bytes)	Ave (μs)	Std (μs)	Min (μs)	Max (μs)	50% (μs)	90% (μs)	99% (μs)	99.99% (μs)	99.9999% (μs)
32	20	4.4	19	295	20	21	22	50	295
64	20	3.7	19	300	20	21	22	55	300
128	20	5.8	20	303	21	21	22	34	303
256	21	1.7	20	304	21	21	23	45	304
512	21	4.2	20	300	21	22	23	33	300
1024	25	7.2	22	303	27	28	29	37	303
2048	30	9.3	25	1022	30	33	57	548	1022
4096	34	16.8	30	966	32	36	65	798	966
8192	46	8.4	39	325	42	59	62	70	325
16384	92	27.6	50	364	91	127	146	181	364
32768	179	11.8	71	550	179	181	182	196	550
63000	193	17.2	111	1070	194	195	197	232	1070

• Reliable

Sample Size (Bytes)	Ave (μs)	Std (μs)	Min (μs)	Max (μs)	50% (μs)	90% (μs)	99% (μs)	99.99% (μs)	99.9999% (μs)
32	22	4.5	21	156	22	23	26	40	156
64	22	2.4	21	120	22	22	24	38	120
128	22	4.1	21	682	22	23	25	40	682
256	24	4.9	21	128	23	32	41	56	128
512	25	5.5	22	144	23	33	41	49	144
1024	26	8.0	23	148	26	29	54	59	148
2048	30	9.3	25	1022	30	33	57	548	1022
4096	34	16.8	30	966	32	36	65	798	966
8192	48	11.7	41	224	44	61	87	116	224
16384	97	30.1	52	362	97	140	157	176	362
32768	178	17.6	84	629	181	188	190	235	629
63000	194	20.2	115	1098	195	197	202	228	1098

Perftest Scripts

To produce these tests, we executed RTI Perftest for C#. The exact script used can be found here:

#!/bin/bash
filename=$0
script_location=$(cd "$(dirname "$filename")" || exit 255; pwd)

export datasizes="32 64 128 256 512 1024 2048 4096 8192 16384 32768 63000"
export datasizes_extended="${datasizes} 100000 500000 1048576 1548576 4194304 10485760"

export domain="2"
export exec_time=20
export num_reps=1
export instance_number=100000
export core=0

# We will use some colors to improve visibility of errors and info messages.
RED='\033[0;31m'
GREEN='\033[0;32m'
YELLOW='\033[0;33m'
BLUE='\033[0;34m'
LIGHTBLUE='\033[0;36m'
NC='\033[0m'
INFO_TAG="${GREEN}[INFO]:${NC}"
WARNING_TAG="${YELLOW}[WARNING]:${NC}"
ERROR_TAG="${RED}[ERROR]:${NC}"

export ip_machine_1="10.2.75.20"
export ip_machine_2="10.2.75.21"
export if10Gbps="enp1s0f0"
export if1Gbps="eno1"

################################################################################

function disable_colors() {
    export RED=""
    export GREEN=""
    export YELLOW=""
    export NC=""
    export BLUE=""
    export LIGHTBLUE=""
    export INFO_TAG="${GREEN}[INFO]:${NC}"
    export WARNING_TAG="${YELLOW}[WARNING]:${NC}"
    export ERROR_TAG="${RED}[ERROR]:${NC}"
}

function change_domain() {
    if [[ "$domain" == "1" ]]; then
        export domain="2"
    else
        export domain="1"
    fi
}

# Usage: execute_test <keyed/unkeyed> <rel/be> <datasizes> <batchSize>
function execute_test() {

    local keyed_unkeyed=$1
    local rel_be=$2
    local datasizes_test=$3
    local other_args=$4
    local name_suffix=$5

    local commands_string_test=$commands_string
    local tag=""

    if [[ "${keyed_unkeyed}" == "keyed" ]]; then
        commands_string_test="${commands_string_test} -keyed -instances $instance_number"
        tag="[${YELLOW}${transport}${NC}|${BLUE}K${NC}|"
    else
        tag="[${YELLOW}${transport}${NC}|${LIGHTBLUE}UK${NC}|"
    fi

    if [[ "${rel_be}" == "be" ]]; then
        commands_string_test="${commands_string_test} -bestEffort"
        tag="${tag}${YELLOW}BE${NC}]"
    else
        tag="${tag}${RED}REL${NC}]"
    fi

    tag="${tag}[${LIGHTBLUE}${lat_thr}${NC}]"

    local output_file=$output_folder/${lat_thr}_${role}_${keyed_unkeyed}_${rel_be}${name_suffix}.csv

    if [[ "$role" == "pub" ]]; then
        echo -e "${YELLOW}[TEST]: $keyed_unkeyed, $rel_be. ${NC}"
    fi

    if [[ "$LANGUAGE" != "java" && "$LANGUAGE" != "cs" ]]; then
        export pre_command_string="taskset -c $core"
    fi

    # Get the aprox time this will take:
    total_tests=$((`wc -w <<< "$datasizes_test"` * num_reps))
    total_time=$((total_tests * exec_time))

    touch $output_file
    local no_headers=""
    local current_test=0
    for index in $(seq 1 ${num_reps}); do
        for DATALEN in ${datasizes_test}; do
            current_test=$((current_test + 1))
            export command="$pre_command_string $executable -domain $domain -dataLen $DATALEN $commands_string_test $other_args $no_headers"
            if [[ "$role" == "pub" ]]; then
                echo -e "Test ${tag} (${current_test}/${total_tests}) -- Total time = ${total_time}s"
                echo -e ${BLUE}$command${NC}
            else
                echo -e ${LIGHTBLUE}$command${NC}
            fi
            if [[ "$LANGUAGE" == "cs" && "$role" == "pub" ]]; then
                sleep 3
            fi
            $command >> $output_file;
            no_headers=" -noOutputHeaders"
            change_domain
        done
    done
}

################################################################################
# PARSE COMMAND LINE OPTIONS:

while [ "$1" != "" ]; do
    case $1 in
        --executable)
            executable=$2
            shift
            ;;
        --output-folder)
            output_folder=$2
            shift
            ;;
        --role)
            export role=$2
            shift
            ;;
        --core)
            export core=$2
            shift
            ;;
        --test-kind)
            export lat_thr=$2
            shift
            ;;
        --interface1)
            export interface=$2
            shift
            ;;
        --interface2)
            export interface2=$2
            shift
            ;;
        --ip1)
            export ip1=$2
            shift
            ;;
        --ip2)
            export ip2=$2
            shift
            ;;
        --repetitions)
            export num_reps=$2
            shift
            ;;
        --domain)
            export domain=$2
            shift
            ;;
        --execution-time)
            export exec_time=$2
            shift
            ;;
        --transport)
            export transport=$2
            shift
            ;;
        --datalen)
            export datalen_input=$2
            shift
            ;;
        --file-suffix)
            export file_suffix=$2
            shift
            ;;
        --executable-suffix)
            export executable_suffix=$2
            shift
            ;;
        --extra-arguments)
            export extra_arguments=$2
            shift
            ;;
        --extra-arguments-pub)
            export extra_arguments_pub=$2
            shift
            ;;
        --extra-arguments-sub)
            export extra_arguments_sub=$2
            shift
            ;;
        --skip-no-batching)
            export skip_no_batching="1"
            ;;
        --skip-be)
            export skip_be_tests="1"
            ;;
        --skip-rel)
            export skip_rel_tests="1"
            ;;
        --skip-keyed)
            export skip_keyed_data="1"
            ;;
        --skip-large-data)
            export skip_large_data="1"
            ;;
        --large-data)
            export large_data="1"
            ;;
        --keyed)
            export skip_unkeyed="1"
            ;;
        --unkeyed)
            export skip_keyed_data="1"
            ;;
        --no-batching)
            export no_batching_only="1"
            ;;
        --reliable)
            export skip_be_tests="1"
            ;;
        --best-effort)
            export skip_rel_tests="1"
            ;;
        --security)
            export security_only="$2"
            shift
            ;;
        --micro)
            export micro="1"
            ;;
        --tss)
            export tss="1"
            ;;
        --no-colors)
            export NO_COLORS="1"
            ;;
        --language)
            export LANGUAGE=$2
            shift
            ;;
        *)
            echo -e "unknown parameter \"$1\""
            exit 255
            ;;
    esac
    shift
done

if [[ "$NO_COLORS" == "1" ]]; then
    disable_colors
fi

export folder_base="$(dirname "${executable}")"/../../..

if [[ $LANGUAGE == "java"  || "$LANGUAGE" == "cs" ]]; then
    export folder_base="$(dirname "${executable}")"/../..
fi
if [[ $tss == "1" ]]; then
    export folder_base="$(dirname "${executable}")"/../../../../..
fi

if [[ "${executable_suffix}" != "" ]]; then
    export executable="${executable}${executable_suffix}"
fi

echo -e "${INFO_TAG} Perftest executable is: $executable"
echo -e "${INFO_TAG} Output folder is: $output_folder"

################################################################################

if [[ "${skip_large_data}" == "1" ]]; then
    export datasizes_extended=${datasizes}
elif [[ "${large_data}" == "1" ]]; then
    export datasizes=${datasizes_extended}
fi

if [[ "${datalen_input}" != "" ]]; then
    echo -e "${YELLOW}[TEST] Testing only for ${datalen_input}${NC}"
    export datasizes=${datalen_input}
    export datasizes_extended=${datalen_input}
    if [[ "${no_batching_only}" != "1" ]]; then
        export skip_large_data="1"
    fi
fi

if [[ "$role" != "pub" && "$role" != "sub" ]]; then
    echo -e "${ERROR_TAG} It must be either publisher or subscriber"
    exit 255
fi

if [[ "$lat_thr" != "thr" && "$lat_thr" != "lat" ]]; then
    echo -e "${ERROR_TAG} It must be either lat or thr"
    exit 255
fi

if [[ "${interface}" == "" ]]; then
    echo "Using default nics"
    export nic_publisher=${ip_machine_1}
    export nic_subscriber=${ip_machine_2}
else
    export nic_publisher=$interface
    echo -e "${INFO_TAG} Using nic_publisher: ${nic_publisher}"

    if [[ "${interface2}" == "" ]]; then
        export nic_subscriber=$interface
    else
        export nic_subscriber=$interface2
    fi
    echo -e "${INFO_TAG} Using nic_subscriber: ${nic_subscriber}"

    if [[ "${ip1}" != "" ]]; then
        export ip_publisher=$ip1
        echo "Using ip_publisher: ${ip_publisher}"
    fi

    if [[ "${ip2}" != "" ]]; then
        export ip_subscriber=$ip2
        echo "Using ip_subscriber: ${ip_subscriber}"
    fi

fi

export transport_string="-transport $transport"

if [[ "$transport" == "UDPv4" ]]; then

    export transport_string_pub="$transport_string -nic $nic_publisher"
    export transport_string_sub="$transport_string -nic $nic_subscriber"

    if [[ "$micro" == "1" ]]; then
        export transport_string_pub="$transport_string_pub -peer ${ip_subscriber}"
        export transport_string_sub="$transport_string_sub -peer ${ip_publisher}"
    fi

elif [[ "$transport" == "TCP" ]]; then
    export transport_string_pub="$transport_string \
        -nic $nic_publisher \
        -peer 0@tcpv4_lan://${ip_subscriber}:7400"
    export transport_string_sub="$transport_string \
        -nic $nic_subscriber \
        -peer 0@tcpv4_lan://${ip_publisher}:7400"
elif [[ "$transport" == "TLS" ]]; then
    export transport_string_pub="$transport_string \
        -nic $nic_publisher \
        -peer tlsv4_lan://${ip_subscriber}:7400"
    export transport_string_sub="$transport_string \
        -nic $nic_subscriber \
        -peer tlsv4_lan://${ip_publisher}:7400"
elif [[ "$transport" == "UDPv4_WAN" ]]; then
    export transport_string_pub="$transport_string \
        -nic $nic_publisher \
        -transportPublicAddress $ip_publisher:7400"
    export transport_string_sub="$transport_string \
        -nic $nic_subscriber \
        -peer 0@udpv4_wan://${ip_publisher}:7400"
else
    export transport_string_pub="$transport_string"
    export transport_string_sub="$transport_string"
fi

################################################################################

export pub_string="-pub \
        ${transport_string_pub} \
        -noPrintIntervals \
        -executionTime $exec_time"

if [[ ${lat_thr} == "lat" ]]; then
    export pub_string="$pub_string \
        -latencyTest"
fi

export sub_string="-sub \
        ${transport_string_sub} \
        -noPrintIntervals"

if [[ "$role" == "pub" ]]; then
    echo -e "$INFO_TAG Publisher side running"
    export commands_string=${pub_string}
    export extra_arguments="${extra_arguments} ${extra_arguments_pub}"
else
    echo -e "$INFO_TAG Subscriber side running"
    export commands_string=${sub_string}
    export extra_arguments="${extra_arguments} ${extra_arguments_sub}"
fi

###############################################################################

echo -e "${INFO_TAG} Executing: /set_${lat_thr}_mode.sh"
sudo /set_${lat_thr}_mode.sh
sleep 5

cd $folder_base
echo -e "${INFO_TAG} Folder Base is: $PWD"
mkdir -p $output_folder

# Tests that may use batching (when doing throughput tests)
if [[ ${no_batching_only} != "1" ]]; then

    # UNKEYED
    if [[ "${skip_unkeyed}" == "" ]]; then

        # RELIABLE
        if [[ "${skip_rel_tests}" == "" ]]; then
            execute_test "unkeyed" "rel" "${datasizes_extended}" "${extra_arguments}" "$file_suffix"
        fi

        # BEST EFFORT
        if [[ "${skip_be_tests}" == "" ]]; then
            execute_test "unkeyed" "be" "${datasizes}" "${extra_arguments}" "$file_suffix"
        fi
    fi

    # KEYED
    if [[ "${skip_keyed_data}" == "" ]]; then

        # RELIABLE
        if [[ "${skip_rel_tests}" == "" ]]; then
            execute_test "keyed" "rel" "${datasizes}" "${extra_arguments}" "$file_suffix"
        fi

        # BEST EFFORT
        if [[ "${skip_be_tests}" == "" ]]; then
            execute_test "keyed" "be" "${datasizes}" "${extra_arguments}" "$file_suffix"
        fi
    fi

fi

if [[ "${skip_no_batching}" == "" || "${no_batching_only}" == "1" ]]; then
    no_batching_tests="1"
fi

# Tests that will not use batching
if [[ "${lat_thr}" == "thr" && "${no_batching_tests}" == "1" ]]; then

    if [[ "$role" == "pub" ]]; then
        export commands_string="${commands_string} -batchSize 0"
    fi

    # UNKEYED
    if [[ "${skip_unkeyed}" == "" ]]; then

        # RELIABLE
        if [[ "${skip_rel_tests}" == "" ]]; then
            execute_test "unkeyed" "rel" "${datasizes}" "${extra_arguments}" "_noBatch${file_suffix}"
        fi

        # BEST EFFORT
        if [[ "${skip_be_tests}" == "" ]]; then
            execute_test "unkeyed" "be" "${datasizes}" "${extra_arguments}" "_noBatch${file_suffix}"
        fi
    fi
fi

#!/bin/bash
filename=$0
script_location=$(cd "$(dirname "$filename")" || exit 255; pwd)

echo -e "[Calling base_script/script.sh]"
"${script_location}/../base_script/script.sh" $@ --transport UDPv4

Test Hardware

The following hardware was used to perform these tests:

Linux Nodes

Dell R340 Servers (13 Units)
Processor: Intel Xeon E-2278G (3.4-5GHz, 8c/16t, 16MB cache, 2 memory channels @2666MHz)
RAM: 4x 16GB 2666MHz DIMM (64GB RAM)
HD: 480GB SATA SSD
NIC 1: Intel 710 dual port 10Gbps SFP
OS: Ubuntu 20.04 -- gcc 9.3.0

Switch

Dell 2048 -- 10Gbps switch